Money A2Z Web Search

Search results

  1. Results From The WOW.Com Content Network
  2. Drill bit sizes - Wikipedia

    en.wikipedia.org/wiki/Drill_bit_sizes

    Below is a chart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for .25, .5, and .75 are shown to thousandths [.250, .500, .750], which is how machinists usually think about them ["two-fifty", "five hundred", "seven-fifty"]. Machinists generally ...

  3. List of drill and tap sizes - Wikipedia

    en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

    The major minus pitch technique also works for inch-based threads, but you must first calculate the pitch by converting the fraction of threads-per-inch (TPI) into a decimal. For example, a screw with a pitch of 1/20 in (20 threads per inch) has a pitch of 0.050 in and a 1 ⁄ 13 in pitch (13 threads per inch) has a pitch of 0.077 in.

  4. Snellen chart - Wikipedia

    en.wikipedia.org/wiki/Snellen_chart

    Snellen chart. Purpose. Snellen chart is used to estimate visual acuity (last three rows are 20/15, 20/13 and 20/10) A Snellen chart is an eye chart that can be used to measure visual acuity. Snellen charts are named after the Dutch ophthalmologist Herman Snellen who developed the chart in 1862 as a measurement tool for the acuity formula ...

  5. List of unusual units of measurement - Wikipedia

    en.wikipedia.org/wiki/List_of_unusual_units_of...

    A board foot is a United States and Canadian unit of approximate volume, used for lumber. It is equivalent to 1 inch × 1 foot × 1 foot (144 cu in or 2,360 cm 3). It is also found in the unit of density pounds per board foot. In Australia and New Zealand the terms super foot or superficial foot were formerly used for this unit. The exact ...

  6. French catheter scale - Wikipedia

    en.wikipedia.org/wiki/French_catheter_scale

    French catheter scale. The French scale, French gauge or Charrière system is commonly used to measure the size of a catheter. It is most often abbreviated as Fr, but can often be seen abbreviated as Fg, FR or F. It may also be abbreviated as CH or Ch (for Charrière, its inventor). However, simply gauge, G or GA generally refers to Birmingham ...

  7. Visual acuity - Wikipedia

    en.wikipedia.org/wiki/Visual_acuity

    For 6/6 = 1.0 acuity, the size of a letter on the Snellen chart or Landolt C chart is a visual angle of 5 arc minutes (1 arc min = 1/60 of a degree), which is a 43 point font at 20 feet. [10] By the design of a typical optotype (like a Snellen E or a Landolt C), the critical gap that needs to be resolved is 1/5 this value, i.e., 1 arc min.

  8. Template:Height - Wikipedia

    en.wikipedia.org/wiki/Template:Height

    The template is intended for conversion of heights specified in either metres or in feet and inches. Template parameters [Edit template data] Parameter Description Type Status Metres m metre metres meter meters The height in metres. Do not use if feet and inches are specified. Number optional Centimetres cm centimetre centimetres centimeter centimeters The height in centimetres. Do not use if ...

  9. Point (typography) - Wikipedia

    en.wikipedia.org/wiki/Point_(typography)

    In typography, the point is the smallest unit of measure. It is used for measuring font size, leading, and other items on a printed page. The size of the point has varied throughout printing's history. Since the 18th century, the size of a point has been between 0.18 and 0.4 millimeters. Following the advent of desktop publishing in the 1980s ...